ISO 25980:2014 : Health and safety in welding and allied processes - Transparent welding curtains, strips and screens for arc welding processes

October 1, 2014, 5:01 am

≫ Next: ISO 27126:2014 : Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification

≪ Previous: ISO 2440:1997/Amd2:2014 : - Amendment 2

ISO 25980:2014 specifies safety requirements for transparent welding curtains, strips, and screens to be used for shielding of work places from their surroundings where arc welding processes are used. They are designed to protect people who are not involved in the welding process from hazardous radiant emissions from welding arcs and spatter.

Welding curtains, strips, and screens it specifies are not intended to replace welding filters. For intentional viewing of welding arcs other means of protection are used.

It is not applicable for welding processes where laser radiation is used.

NOTE Darker welding curtains or screens are advisable for mutual separation of adjacent work places for reasons of comfort.

↧

ISO 27126:2014 : Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification

October 1, 2014, 5:01 am

≫ Next: ISO 2813:2014 : Paints and varnishes - Determination of gloss value at 20 degrees, 60 degrees and 85 degrees

≪ Previous: ISO 25980:2014 : Health and safety in welding and allied processes - Transparent welding curtains, strips and screens for arc welding processes

ISO 27126:2014 specifies requirements for four types of thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for carrying hydrocarbons, solvents and chemicals. It specifies bore sizes from 25 mm to 300 mm, working pressures from 0,4 MPa (4 bar) to 1,4 MPa (14 bar) and working temperatures from -30 °C to 150 °C, according to type.

Type 1 hoses are suitable for vapour applications. Types 2 to 4 hoses are suitable for liquid applications.

↧

ISO 2813:2014 : Paints and varnishes - Determination of gloss value at 20 degrees, 60 degrees and 85 degrees

October 1, 2014, 5:01 am

≫ Next: ISO 4097:2014 : Rubber, ethylene-propylene-diene (EPDM) - Evaluation procedure

≪ Previous: ISO 27126:2014 : Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification

ISO 2813:2014 specifies a method for determining the gloss of coatings using the three geometries of 20°, 60° or 85°. The method is suitable for the gloss measurement of non-textured coatings on plane, opaque substrates.

↧

ISO 4097:2014 : Rubber, ethylene-propylene-diene (EPDM) - Evaluation procedure

October 1, 2014, 5:01 am

≫ Next: ISO 4659:2014 : Styrene-butadiene rubber (carbon black or carbon black and oil masterbatches) - Evaluation procedure

≪ Previous: ISO 2813:2014 : Paints and varnishes - Determination of gloss value at 20 degrees, 60 degrees and 85 degrees

ISO 4097:2014 specifies physical and chemical tests on raw rubbers; standard materials, standard test formulations, equipment, and processing methods for evaluating the vulcanization characteristics of ethylene-propylene-diene rubbers (EPDM), including oil-extended types.

↧

ISO 4659:2014 : Styrene-butadiene rubber (carbon black or carbon black and oil masterbatches) - Evaluation procedure

October 1, 2014, 5:01 am

≫ Next: ISO 4995:2014 : Hot-rolled steel sheet of structural quality

≪ Previous: ISO 4097:2014 : Rubber, ethylene-propylene-diene (EPDM) - Evaluation procedure

ISO 4659:2014 specifies physical and chemical tests on raw rubbers; standard materials, standard test formulations, equipment, and processing methods for evaluating the vulcanization characteristics of styrene-butadiene rubber masterbatches with carbon black or with carbon black and oil.

↧

ISO 4995:2014 : Hot-rolled steel sheet of structural quality

October 1, 2014, 5:01 am

≫ Next: ISO 630-5:2014 : Structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance

≪ Previous: ISO 4659:2014 : Styrene-butadiene rubber (carbon black or carbon black and oil masterbatches) - Evaluation procedure

ISO 4995:2014 applies to hot-rolled steel sheet of structural quality in the grades listed in Table 1, usually prepared without the use of microalloying elements. The product is intended for structural purposes where particular mechanical properties are required. It is generally used in the delivered condition and is intended for bolted, riveted, or welded structures. This product is produced on a wide strip mill, not a plate mill.

This International Standard does not cover steels intended for boilers or pressure vessels, steels designated as commercial quality or drawing quality (covered in ISO 3573^[1]), steels to be re-rolled to cold-reduced products, or steels designated as weathering steels, having increased atmospheric corrosion resistance.

↧

ISO 630-5:2014 : Structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance

October 1, 2014, 5:01 am

≫ Next: ISO 630-6:2014 : Structural steels - Part 6: Technical delivery conditions for seismic-proof improved structural steels for building

≪ Previous: ISO 4995:2014 : Hot-rolled steel sheet of structural quality

ISO 630-5:2014 specifies qualities for steels with improved atmospheric corrosion resistance for general structural use. It applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are used in the usual delivery conditions as given in 6.3, and normally intended for welded or bolted structures.

It covers nine (9) grades and four (4) qualities. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements.

It does not include the following structural steels, certain of which are covered by other International Standards: sheet and strip ? refer to ISO TC 17/SC 12 "Continuous mill flat rolled products"; tubular products ? refer to ISO TC 5/SC 1 "Steel tubes".

↧

ISO 630-6:2014 : Structural steels - Part 6: Technical delivery conditions for seismic-proof improved structural steels for building

October 1, 2014, 5:01 am

≫ Next: ISO 6362-7:2014 : Wrought aluminium and aluminium alloys - Extruded rods/bars, tubes and profiles - Part 7: Chemical composition

≪ Previous: ISO 630-5:2014 : Structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance

ISO 630-6:2014 specifies qualities for seismic-proof improved structural steels. It applies to steel plates with thicknesses of 6 mm or over and up to 125 mm, wide flats and hot-rolled sections up to 140 mm, which are used in the usual delivery conditions as given in 6.2 and normally intended for welded or bolted structures.

It does not include the following structural steels, certain of which are covered by other International Standards: sheet and strip ? refer to ISO TC 17/SC 12, Continuous mill flat rolled products; tubular products ? refer to ISO TC 5/SC 1, Steel tubes.

↧

ISO 6362-7:2014 : Wrought aluminium and aluminium alloys - Extruded rods/bars, tubes and profiles - Part 7: Chemical composition

October 1, 2014, 5:01 am

≫ Next: ISO 6506-1:2014 : Metallic materials - Brinell hardness test - Part 1: Test method

≪ Previous: ISO 630-6:2014 : Structural steels - Part 6: Technical delivery conditions for seismic-proof improved structural steels for building

ISO 6362-7:2014 specifies the chemical composition of wrought aluminium and aluminium alloys. The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association (known as the "Teal Sheets"), for the corresponding alloys.

↧

ISO 6506-1:2014 : Metallic materials - Brinell hardness test - Part 1: Test method

October 1, 2014, 5:01 am

≫ Next: ISO 6506-2:2014 : Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing machines

≪ Previous: ISO 6362-7:2014 : Wrought aluminium and aluminium alloys - Extruded rods/bars, tubes and profiles - Part 7: Chemical composition

ISO 6506-1:2014 specifies the method for the Brinell hardness test for metallic materials. It is applicable to both fixed location and portable hardness testing machines.

For some specific materials and/or products, particular International Standards exist (e.g. ISO 4498) and make reference to this International Standard.

↧

ISO 6506-2:2014 : Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing machines

October 1, 2014, 5:01 am

≫ Next: ISO 6506-3:2014 : Metallic materials - Brinell hardness test - Part 3: Calibration of reference blocks

≪ Previous: ISO 6506-1:2014 : Metallic materials - Brinell hardness test - Part 1: Test method

ISO 6506-2:2014 specifies methods of direct and indirect verification of testing machines used for determining Brinell hardness in accordance with ISO 6506-1, and also specifies when these two types of verification has to be performed.

The direct verification involves checking that individual machine performance parameters fall within specified limits whereas the indirect verification utilizes hardness measurements of reference blocks, calibrated in accordance with ISO 6506-3, to check the machine's overall performance.

If a testing machine is also to be used for other methods of hardness testing, it has to be verified independently for each method.

ISO 6506-2:2014 is applicable to both fixed location and portable hardness testing machines. For machines that are incapable of satisfying the specified force-time profile, the direct verification of force and testing cycle can be modified by the use of Annex B.

↧

ISO 6506-3:2014 : Metallic materials - Brinell hardness test - Part 3: Calibration of reference blocks

October 1, 2014, 5:01 am

≫ Next: ISO 6506-4:2014 : Metallic materials - Brinell hardness test - Part 4: Table of hardness values

≪ Previous: ISO 6506-2:2014 : Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing machines

ISO 6506-3:2014 specifies a method for the calibration of reference blocks to be used in the indirect verification of Brinell hardness testing machines as described in ISO 6506-2.

The procedures necessary to ensure metrological traceability of the calibration machine are also specified.

↧

ISO 6506-4:2014 : Metallic materials - Brinell hardness test - Part 4: Table of hardness values

October 1, 2014, 5:01 am

≫ Next: ISO 6806:2014 : Rubber hoses and hose assemblies for use in oil burners - Specification

≪ Previous: ISO 6506-3:2014 : Metallic materials - Brinell hardness test - Part 3: Calibration of reference blocks

ISO 6506-4:2014 gives a table of the Brinell hardness values for use in tests on flat surfaces.

↧

ISO 6806:2014 : Rubber hoses and hose assemblies for use in oil burners - Specification

October 1, 2014, 5:01 am

≫ Next: ISO 7663:2014 : Halogenated isobutene-isoprene rubber (BIIR and CIIR) - Evaluation procedures

≪ Previous: ISO 6506-4:2014 : Metallic materials - Brinell hardness test - Part 4: Table of hardness values

ISO 6806:2014 specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.

The following two types of hose assembly are specified.

Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 °C.

Type 2: Hose assemblies for insertion between the oil burner pump and the atomizing connection; working pressure 4,0 MPa (40 bar); maximum oil temperature 100 °C.

↧

ISO 7663:2014 : Halogenated isobutene-isoprene rubber (BIIR and CIIR) - Evaluation procedures

October 1, 2014, 5:01 am

≫ Next: ISO 8598-1:2014 : Optics and optical instruments - Focimeters - Part 1: General purpose instruments

≪ Previous: ISO 6806:2014 : Rubber hoses and hose assemblies for use in oil burners - Specification

ISO 7663:2014 specifies the following:

- physical and chemical tests on raw rubbers;

- standardized materials, a standardized test formulation, and the equipment and processing methods for evaluating the vulcanization characteristics of all types of halogenated isobutene-isoprene rubber (BIIR and CIIR).

↧

ISO 8598-1:2014 : Optics and optical instruments - Focimeters - Part 1: General purpose instruments

October 1, 2014, 5:01 am

≫ Next: ISO 9308-1:2014 : Water quality - Enumeration of Escherichia coli and coliform bacteria - Part 1: Membrane filtration method for waters with low bacterial background flora

≪ Previous: ISO 7663:2014 : Halogenated isobutene-isoprene rubber (BIIR and CIIR) - Evaluation procedures

ISO 8598-1:2014 specifies requirements and test methods for general purpose focimeters designed for the measurement of vertex powers, cylinder axis, prismatic power and prism base setting within a restricted area at a specified location of a lens. This excludes instruments that can only measure the whole lens at once.

It is applicable to instruments typically intended for use by the ophthalmic community, with the capability to demonstrate conformity of spectacle lens products with the International Standards existing for these lenses.

↧

ISO 9308-1:2014 : Water quality - Enumeration of Escherichia coli and coliform bacteria - Part 1: Membrane filtration method for waters with low bacterial background flora

October 1, 2014, 5:01 am

≫ Next: ISO/IEC 1539-1:2010/Cor3:2014 : Corrigendum

≪ Previous: ISO 8598-1:2014 : Optics and optical instruments - Focimeters - Part 1: General purpose instruments

ISO 9308-1:2014 specifies a method for the enumeration of Escherichia coli (E. coli) and coliform bacteria. The method is based on membrane filtration, subsequent culture on a chromogenic coliform agar medium, and calculation of the number of target organisms in the sample. Due to the low selectivity of the differential agar medium, background growth can interfere with the reliable enumeration of E. coli and coliform bacteria, for example, in surface waters or shallow well waters. This method is not suitable for these types of water.

ISO 9308-1:2014 is especially suitable for waters with low bacterial numbers that will cause less than 100 total colonies on chromogenic coliform agar (CCA). These may be drinking water, disinfected pool water, or finished water from drinking water treatment plants.

Some strains of E. coli which are β-D-glucuronidase negative, such as Escherichia coli O157, will not be detected as E. coli. As they are β-D-galactosidase positive, they will appear as coliform bacteria on this chromogenic agar.

↧

ISO/IEC 1539-1:2010/Cor3:2014 : Corrigendum

October 1, 2014, 5:01 am

≫ Next: ISO/IEC 17811-3:2014 : Information Technology - Device control and management - Part 3: Specification of Reliable Message Delivery Protocol

≪ Previous: ISO 9308-1:2014 : Water quality - Enumeration of Escherichia coli and coliform bacteria - Part 1: Membrane filtration method for waters with low bacterial background flora

↧

ISO/IEC 17811-3:2014 : Information Technology - Device control and management - Part 3: Specification of Reliable Message Delivery Protocol

October 1, 2014, 5:01 am

≫ Next: ISO/IEC 18031:2011/Cor1:2014 : Corrigendum

≪ Previous: ISO/IEC 1539-1:2010/Cor3:2014 : Corrigendum

ISO/IEC 17811-3:2014 provides the specification of Reliable Message Delivery Protocol (RMDP), which is an application-layer protocol used to provide uniform and reliable message delivery among devices regardless of the underlying network protocols or interfaces.

The network security is out of scope in this part of ISO/IEC 17811. However, the security services might be necessary according to applications of RMDP. RMDP might suffer from many network-specific threats. To countermeasure those threats, some security mechanism can be deployed.

↧