Latest Standards From Techstreet

The present document specifies the procedures for the conformance test of the measurement requirements for FDD or TDD mode of UTRA and FDD or TDD mode of E-UTRA for the User Equipment (UE) that supports one or more of the defined positioning methods. These positioning methods are for UTRA: Assisted Global Positioning System (AGPS), Assisted Global Navigation Satellite Systems (A-GNSS) and for E-UTRA: Assisted Global Navigation Satellite System (A-GNSS), Observed Time Difference of Arrival (OTDOA), Enhanced Cell ID (ECID).

Tests are only applicable to those mobiles that are intended to support the appropriate functionality. To indicate the circumstances in which tests apply, this is noted in the "Test applicability" part of the test.

The Implementation Conformance Statement (ICS) pro-forma could be found in the 3rd part of the present document.

ETSI TR 137 977 is the technical report for the work item on MIMO OTA, which was approved at TSG RAN#55 [13]. The scope of the WI is to define a 3GPP methodology or set of comparable methodologies for measuring the radiated performance of multiple antenna reception and MIMO receivers in the UE. The test methodology should be relevant for HSPA and LTE technologies, with particular focus on handheld devices and devices embedded in laptop computers.

RAN WG4 has been working on the study item "Measurement of radiated performance for MIMO and multi-antenna reception for HSPA and LTE terminals" with the objective to define a test methodology for measuring the radiated performance of MIMO and multi-antenna UE reception in UMTS and LTE.

RAN4 has done sufficient work to be confident that the definition of a meaningful test methodology is feasible; however RAN4 does not have sufficient evidence yet to conclude on a single test methodology that would fulfil all requirements for standardisation, and the standardisation of multiple test methodologies may be one eventual outcome, with a view to avoid differences in the decision of what is a "good" or "bad" device from the radiated receiver performance perspective.

ETSI TR 145 926 provides a study into BTS energy saving solutions. The present document analyses and evaluates different solutions to determine the benefits provided compared to the legacy BTS energy consumption.

In the scope of this study there are following solutions:

Reduction of Power on the BCCH carrier (potentially enabling dynamic adjustment of BCCH power)
Reduction of power on DL common control channels
Reduction of power on DL channels in dedicated mode, DTM and packet transfer mode
Deactivation of cells (e.g. Cell Power Down and Cell DTX like concepts as discussed in RAN [4])
Deactivation of other RATs in areas with multi-RAT deployments, for example, where the mobile station could assist the network to suspend/minimize specific in-use RATs at specific times of day
And any other radio interface impacted power reduction solutions

The solutions will also consider the following aspects:

Impacts on the time for legacy and new mobile stations to gain access to service from the BTS
Impacts on legacy and new mobile stations to keep the ongoing service (without increasing drop rate)
Impacts on legacy and new mobile stations implementation and power consumption, e.g. due to reduction in DL power, cell (re-)selection performance, handover performance, etc.
Impacts on UL/DL coverage balance, especially to CS voice

Solutions will be considered for both BTS energy saving non-supporting and supporting mobile stations (i.e. solutions that are non-backwards compatible towards legacy mobile stations will be out of the scope of this study).

The contents of the present document when stable will determine the modifications to existing GERAN specifications.

The present document specifies the protocol conformance testing for the 3rd Generation UTRAN and E-UTRAN User Equipment (UE) supporting UE positioning. This is the second part of a multi-part test specification. The following information can be found in this part:

the overall protocol conformance test structure;
the protocol conformance test configurations;
the conformance requirement and reference to the core specifications;
the test purposes; and
a brief description of the test procedure, the specific test requirements and short message exchange table.

The Implementation Conformance Statement (ICS) pro-forma could be found in the 3rd part of the present document.

The present document is valid for UE supporting UE positioning implemented according to 3GPP releases starting from Release 99 up to the Release indicated on the cover page of the present document.

The present document provides the Implementation Conformance Statement (ICS) proforma for 3rd Generation UTRAN and E-UTRAN User Equipment (UE) supporting UE positioning, in compliance with the relevant requirements, and in accordance with the relevant guidance given in ISO/IEC 9646-1 [7] and ISO/IEC 9646-7 [8].

The present document also specifies a recommended applicability statement for the test cases included in 3GPP TS 37.571-1 [5] and 3GPP TS 37.571-2 [6]. These applicability statements are based on the features implemented in the UE.

Special conformance testing functions can be found in 3GPP TS 34.109 [10] for UTRA and 3GPP TS 36.509 [2] for EUTRA. The common test environments are included in 3GPP TS 34.108 [9] for UTRA and in 3GPP TS 36.508 [3] for E-UTRA.

The present document is valid for UE supporting UE positioning implemented according to 3GPP releases starting from Release 99 up to the Release indicated on the cover page of the present document.

The present document identifies the 3GPP system specifications for Release 11. The specifications and reports of 3GPP Release 11 have a major version number 11 (i.e. 11.x.y). The listed Specifications are required to build a system based on GERAN radio technology.

Proceedings of the PM2014 World Congress on Powder Metallurgy & Particulate Materials, May 18-22, Orlando, Florida.
Contains 200 technical papers encompassing over 2,000 pages in pdf format that preserves the original color in all figures.

Contents include the following sections:
Part 1 - Design & Modeling of PM Materials, Components & Processes
Part 2 - Particulate Production
Part 3 - General Compaction & Forming Processes
Part 4 - Powder Injection Molding (Metals & Ceramics)
Part 5 - Pre-Sintering & Sintering
Part 6 - Secondary Operations
Part 7 - Materials
Part 8 - Refractory Metals, Carbides & Ceramics
Part 9 - Advanced Particulate Materials & Processes
Part 10 - Material Properties
Part 11 - Test & Evaulation
Part 12 - Applications
Part 13 - Management Issues

ETSI TS 132 536 specifies the Solution Set definitions for the IRP whose semantics are specified in Software Management IRP Information Service (3GPP TS 32.532 [5]).

This Solution Set definitions specification is related to 3GPP TS 32.532 V12.0.X.

ETSI TS 132 541 describes concept and requirements of OAM for Self-Healing of Self-Organizing Networks (SON).

ETSI TS 132 551 describes the concepts and requirements how energy savings functionalities are managed what requirements need to be met to support this. The document also describes if a requirement shall be met via the Itf-N interface or via other means.

ETSI TS 132 571 describes requirements and concepts including architecture supporting Home Node B and Home eNode B OAM&P for interface Type 2.

ETSI TS 132 572 describes requirements and concepts including architecture supporting Home NB and Home eNB OAM&P for interface Type 2.

ETSI TS 132 581 describes the concepts and requirements of OAM for Home NodeB (HNB). The requirements captured in this document shall be met via Type 1 interface between HNB and HMS.

ETSI TS 132 582 describes the architecture for Home NodeB (HNB) Management and Data class definition for Fault Management, Configuration Management and Performance Measurements. The stage 2 definitions captured in this document shall be met via type 1 interface between HNB and Domain Manager.

ETSI TS 132 583 describes the procedure flows between HNB & HMS for the OAM of HNB Management.

ETSI TS 132 584 describes the data format for Configuration Management and Performance Management for Home Node B (HNB). The XML definitions captured in this document shall be met via Type 1 interface between HNB and HNB Management System (HMS).

ETSI TS 132 591 describes the concepts and requirements of OAM for Home eNodeB (HeNB). The requirements captured in this document shall be met via Type 1 interface between HeNB and HeMS.

ETSI TS 132 592 describes the Information Model definition for Fault Management, Configuration Management and Performance measurements of Home eNodeBs.

The stage 2 definitions captured in the present document shall be met via type 1 interface between HeNB and HMS.

ETSI TS 132 593 describes the procedure flows between network entities involved in HeNB managementrelated tasks. These procedures are based on the requirements specified in [4]. Information model for managementrelated information exchanged in these procedures is specified in [5] and references therein. XML file formats used to encapsulate the information exchanged in these procedures are specified in [6]. The communication protocol used for HeNB management is the TR-069 protocol, specified in [7].

Management interface affected by these procedures is the Type 1 interface between HeNB and HeMS. Procedures flows over the Type 2 interface (between Element Management and Network Management layer) for the management of HeNB are outside of scope of this document.

Latest Images