Latest Standards From Techstreet

1. SCOPE

1.1 This Standard establishes performance requirements for Mortise Locks and Latches and includes operational, cycle, strength, material evaluation, security, and finish tests, and dimensional criteria.

1.2 Tests described in this Standard are performed under laboratory conditions. In actual usage, results may vary because of installation, maintenance, and environmental conditions.

1.4 Grade Qualifications (Also see Appendix A)
1.4.1 Two classifications of Grades are described in this Standard. Manufacturers shall indicate separately, for both an Operational Grade and a Security Grade level of mortise locks and latches. The minimum acceptable grade level for Operational and Security grades shall be a grade 3.
1.4.1.1 Operational Grades shall meet the requirements of Sections 8, 9, 10, 11 and 13.
1.4.1.2 Security Grades shall meet the requirements of Section 12.
1.4.2 Any function shall be tested for qualification under Operational Grades and all other functions shall be considered as meeting the criteria provided the lock case and operating parts are of the same construction as that of the lock previously tested.
1.4.3 Function F21 or a similar function with dead bolts and function F04 or a similar function without dead bolts to be certified shall be tested with the trim for qualification under Security Grades. All other functions where access is prevented shall be considered as meeting the criteria provided the lock case and operating parts are of the same construction as that of the lock previously tested.

1.1 This Standard establishes requirements for the performance and installation of gasketing systems including intumescents applied to, or mortised to doors, frames or both. Included are performance tests intended to provide installation guidelines, resistance to smoke and air infiltration, and measure the life and durability of gasketing materials.

1.2 Requirements apply to factory or field installed materials.

1.3 Tests described in this Standard are performed under laboratory conditions. In actual usage, results vary because of installation, maintenance and environmental conditions.

This item is available as part of a discounted standards set covering Trimming of Doors .

1. SCOPE

1.1 This Standard establishes performance requirements for bored and preassembled locks and latches, and includes cycle tests, strength tests, operational tests, security tests, material evaluation tests, finish tests, and dimensional criteria.

1.2 Tests described in this Standard are performed under laboratory conditions. In actual usage, results vary because of installation, door and frame construction, maintenance and environmental conditions.

1.3 Grade Qualifications Manufacturers shall indicate the Grade level of their locks. Locks shall meet all tests for their grade listing. A Grade 1 lock shall meet all Grade 1 criteria, a Grade 2 lock shall meet all Grade 2 criteria, and a Grade 3 lock shall meet all Grade 3 criteria.

This item is available as part of a discounted standards set covering Door Locks.

Cross References:
IEC 60709
IEC 60780
IEC 60987
IEC 61000
IEC 61226
IEC 61513
IEC 62003
IEC 62138
IEC 62645
IEC 62671
IEC/TR 62918:2014
IEC/TS 62657-1:2013
IEC/TS 62657-2:2013

All current amendments available at time of purchase are included with the purchase of this document.

Cross References:
EN 15603:2008
ISO 7345:1987
EN 15316-4-2:2017
EN ISO 7345 EN 15316-3:2017
CEN/TS 16629:2014
ISO 52000-1:2017
ENISO 52000-1
CEN/TS 16628:2014
CENSE report WP6.1_N05rev02

All current amendments available at time of purchase are included with the purchase of this document.

Cross References:
EN ISO 7345:1995
ISO 7345:1987
EN 15603:2008
EN 12831-3 CENSE report WP6.1_N05rev02
ISO 52000-1
CEN/TS 16629:2014
CEN/TS 16628:2014
CENISO/TR 52000-2
ENISO 52000-1
ISO/TR 52000-2

All current amendments available at time of purchase are included with the purchase of this document.

Cross References:
BS EN 60584-1:2013
BS EN ISO 13943:2010 BS 8414-2:2015

Incorporates the following:
Amendment, June 2017; Corrigendum, Septe

All current amendments available at time of purchase are included with the purchase of this document.

Latest Images