Corrigendum Standard - Unapproved Draft.
This corrigendum to IEEE Std 802.3-2015 clarifies which lane of the media dependent interface (MDI) of a multilane Physical Layer entity (PHY) is used as the timestamping reference point.
IEEE P802.3-2015/Cor 1 : IEEE Draft Standard for Ethernet - Corrigendum 1: Multilane Timestamping
↧
↧
IEEE P802.15.4v : IEEE Draft Standard for Low-Rate Wireless Networks Amendment: Enabling/Updating the Use of Regional Sub-GHz Bands
Amendment Standard - Unapproved Draft.
This amendment defines changes to the IEEE Std 802.15.4-2015 SUN PHYs enabling the use of the 870-876 MHz & 915-921 MHz bands in Europe, the 902-928 MHz band in Mexico, the 902-907.5 MHz & 915-928 MHz bands in Brazil, the 915-928 MHz band in Australia/New Zealand and Asian regional frequency bands that are not in IEEE Std 802.15.4-2015. This amendment also changes the channel parameters listed in the SUN PHYs, Low Energy Critical Infrastructure Monitoring (LECIM) PHY and the TV White Space (TVWS) PHY for the 470-510 MHz band in China and the 863-870 MHz band in Europe, and aligns these channel parameters with regional requirements. The amendment includes channel access and/or timing changes to the MAC necessary for conformance to regional requirements for these bands.
↧
IEEE PC62.69a : IEEE Draft Standard for the Surge Parameters of Isolating Transformers used in Networking Devices and Equipment Amendment 1: Addition of 4.5, Saturated Core Secondary Winding Parameters
Amendment Standard - Unapproved Draft.
This amendment adds a new sub-clause 4.5 1 Saturated core secondary winding parameters to IEEE C62.69(TM)-2016. Test methods, test circuits, measurement procedures, and result treatment to determine the secondary winding resistance and saturated core inductance are given.
↧
SAE USCAR17-5 : Performance Specification for Automotive RF Connector Systems
↧
SAE AS6286/6 : Deicing/Anti-Icing Diagrams/No Spray Zones
This document shall be used in conjunction with:
- AS6286, Training and Qualification Program for Deicing/Anti-icing of Aircraft on the Ground
- AS6286/1, Processes Including Methods
- AS6286/2, Equipment
- AS6286/3, Fluids
- AS6286/4, Weather
- AS6286/5, Health, Safety and First Aid
↧
↧
SAE AMS4909K : Titanium Alloy, Sheet, Strip, and Plate 5Al - 2.5Sn, Extra Low Interstitial Annealed
↧
SAE AMS4962B : Titanium Alloy, Investment Castings, 6AL - 4V, Hot Isostatically Pressed (Stabilized: Dec 2016)
↧
SAE AMS6409E : Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340) Special Aircraft Quality Cleanliness Normalized and Tempered
↧
SAE AMST81915B : Titanium and Titanium-Alloy Castings, Investment (Stabilized: Dec 2016)
↧
↧
SAE AS6286/3 : Fluids
Field of Application
This document shall be used in conjunction with:
AS6286 Training and Qualification Program for Deicing/Anti-icing of Aircraft on the Ground
AS6286/1 Processes including Methods
AS6286/2 Equipment
AS6286/4 Weather
AS6286/5 Health, Safety and First Aid
AS6286/6 Aircraft Deicing/Anti-icing Diagrams, No-Spray-Zones
↧
SAE J1939/11_201612 : Physical Layer, 250 Kbps, Twisted Shielded Pair
This document defines a physical layer having a robust immunity to EMI and physical properties suitable for harsh environments.
CAN controllers are available which support the CAN Flexible Data Rate Frame Format. These controllers, when used on SAE J1939-11 networks, must be restricted to use only the Classical Frame Format compliant to ISO 11898-1:2015.
These SAE Recommended Practices are intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
↧
SAE J2601_201612 : Fueling Protocols for Light Duty Gaseous Hydrogen Surface Vehicles
SAE J2601 establishes the protocol and process limits for hydrogen fueling of light duty vehicles. These process limits (including the fuel delivery temperature, the maximum fuel flow rate, the rate of pressure increase and the ending pressure) are affected by factors such as ambient temperature, fuel delivery temperature and initial pressure in the vehicle's compressed hydrogen storage system. SAE J2601 establishes standard fueling protocols based on either a look-up table approach utilizing a fixed pressure ramp rate, or a formula based approach utilizing a dynamic pressure ramp rate continuously calculated throughout the fill. Both protocols allow for fueling with communications or without communications. The table-based protocol provides a fixed end-of-fill pressure target, whereas the formula-based protocol calculates the end-of-fill pressure target continuously. For fueling with communications, this standard is to be used in conjunction with SAE J2799, Hydrogen Surface Vehicle to Station Communications Hardware and Software.
An important factor in the performance of hydrogen fueling is the station's dispensing equipment cooling capability and the resultant fuel delivery temperature. There are three fuel delivery temperature categories denoted by a "T" rating - T40, T30, and T20, where T40 is the coldest. Under reference conditions, SAE J2601 has a performance target of a fueling time of 3 minutes and a State of Charge (SOC) of 95-100% (with communications), which can be achieved with a T40 rated dispenser. However, with higher fuel delivery temperature dispenser ratings (T30 or T20) and/or at high ambient temperatures, fueling times may be longer.
Table 1 below depicts the scope of SAE J2601 and potential work items for future revisions within this or other documents of the J2601 series. SAE J2601 includes protocols which are applicable for two pressure classes (35 and 70 MPa), three fuel delivery temperatures categories (-40 °C, -30 °C, -20 °C) and compressed hydrogen storage system sizes from 49.7 to 248.6 L. Future versions of SAE J2601work may incorporate warmer fuel delivery temperatures (-10 °C and ambient) and smaller compressed hydrogen storage systems for motorcycles and other light duty applications.
The fueling protocols herein were developed based on a set of key assumptions described in Section 7 and Appendix A. These assumptions should be carefully considered in the development and implementation of an on-board compressed hydrogen storage system. In particular, hydrogen storage systems with properties which do not fall within the parameters in Table A3 should be further evaluated to confirm compatibility with the protocols herein.
↧
SAE AMS6304M : Low-Alloy Steel, Heat-Resistant, Bars, Forgings, and Tubing 0.95Cr - 0.55Mo - 0.30V (0.40 - 0.50C)
↧
↧
SAE AMS6415U : Steel, Bars, Forgings, and Tubing 0.80Cr - 1.8Ni - 0.25Mo (0.38 - 0.43C) (SAE 4340)
↧
SAE J3114_201612 : Human Factors Definitions for Automated Driving and Related Research Topics
↧
SAE J1677_201612 : Tests and Procedures for Carbon Steel and High Strength Low Alloy Steel Tubing
↧
ASTM A1103/A1103M-16 : Standard Specification for Seamless Cold-Finished Carbon Steel Structural Frame Tubing for Automotive Racing Applications
1.1 This specification is for seamless cold-finished carbon steel round structural frame tubing for automotive racing applications. The chemical requirements are listed in Table 1. Tubing may be used for other applications requiring similar tolerances and properties. The specification includes requirements for heat treatment and mechanical properties to meet the needs for the application. The tubing is intended to be bent and joined by welding. The welding procedure shall be suitable for the grade, the condition of the components, and the intended service.
(A) The ranges and limits given in this table apply to heat analysis; except as required by 6.1, product analyses are subject to the applicable additional tolerances given in Table 2.
(B) Columbium (Cb) and Niobium (Nb) are alternate names for element 41 in the Periodic Table of the Elements.
1.2 The tubing outside diameter size range is from 0.625 to 2.0 in. [16 to 50 mm]. The wall thickness shall be specified as a minimum wall.
1.3 Optional supplementary requirements may be provided and, when one or more of these are desired, each shall be so stated in the order.
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
↧
↧
ASTM C373-16e1 : Standard Test Methods for Determination of Water Absorption and Associated Properties by Vacuum Method for Pressed Ceramic Tiles and Glass Tiles and Boil Method for Extruded Ceramic Tiles and Non-tile Fired Ceramic Whiteware Products
1.1 These test methods covers procedures for determining water absorption, bulk density, apparent porosity, and apparent specific gravity of non-tile fired unglazed ceramic whiteware products, glazed or unglazed ceramic tiles, and glass tiles.
1.2 The values stated in metric units are normative. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not normative.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
↧
ASTM D228/D228M-16 : Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing
1.1 These test methods cover procedures for sampling, examination, physical testing, and analyses of asphalt-containing materials used in roofing and waterproofing. These materials include but are not limited to roll roofing, cap sheets, and shingles. Any of these materials are allowed to be partially or fully coated, surfaced, or laminated, or a combination thereof.
1.2 The test methods and procedures in this standard appear in the following order:
Section | Content |
|
|
6 | Types of Roofing |
7 | Sampling |
8 | Mass and Area Determination |
9 | Selection of Representative Specimens |
10 | Moisture |
11 | Pliability |
12 | Mass Loss and Behavior on Heating |
13 | Tear Strength |
14 | Fastener Pull-Through Resistance |
15 | Preparation and Selection of Small Test Specimens |
16 | Analysis of Glass Felt Products |
17 | Analysis of Roofing Products with Organic Felts |
18 | Ash of Desaturated Felt |
19 | Calculation |
20 | Adjusting Back Coating Fine Mineral Matter and |
21 | Report |
22 | Precision and Bias |
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
↧
ASTM D7160-16 : Standard Practice for Determination of Expiration Dating for Medical Gloves
1.1 This practice covers all surgeon's and examination gloves made from either synthetic or natural rubber latex. The purpose of this practice is to establish methods for testing medical gloves and analyzing the data to determine their shelf life.
1.2 This standard does not purport to address all of the label claims and safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
↧
More Pages to Explore .....
