ASTM D5677-16 : Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines

September 26, 2016, 4:09 am

≫ Next: ASTM B354-16 : Standard Terminology Relating to Uninsulated Metallic Electrical Conductors

≪ Previous: ASTM D5013-16 : Standard Practices for Sampling Wastes from Pipes and Other Point Discharges

$

0

0

1.1 This specification covers a reinforced plastic pipe and fittings system made from epoxy resin and glass-fiber reinforcement, together with adhesive for joint assembly, intended for service up to 150°F (65.6°C) and 150-psig (1034-kPa) operating pressure and surges up to 275 psig (1896 kPa) in aviation jet turbine fuel lines installed below ground.

1.2 The dimensionless designator NPS has been substituted in this specification for such traditional terms as nominal diameter, size, and nominal size.

1.3 The values stated in inch-pound units are to be regarded as standard. The values in parentheses are for information only.

1.4 The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1: There is no known ISO equivalent to this standard.

---

ASTM B354-16 : Standard Terminology Relating to Uninsulated Metallic Electrical Conductors

September 26, 2016, 4:09 am

≫ Next: ASTM F2608-15e1 : Standard Test Method for Determining the Change in Room Air Particulate Counts as a Result of the Vacuum Cleaning Process

≪ Previous: ASTM D5677-16 : Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines

$

0

0

1.1 This terminology standard defines abbreviations and terms specific to uninsulated electrical conductors. For terms relating to superconductors, see Terminology B713.

ASTM F2608-15e1 : Standard Test Method for Determining the Change in Room Air Particulate Counts as a Result of the Vacuum Cleaning Process

September 26, 2016, 4:09 am

≫ Next: ASTM E133-92(2016) : Standard Specification for Distillation Equipment

≪ Previous: ASTM B354-16 : Standard Terminology Relating to Uninsulated Metallic Electrical Conductors

$

0

0

1.1 This test method provides a laboratory test for the measurement of particulate generated as a direct result of the vacuuming process.

1.2 This test method is applicable to all residential/commercial uprights, canisters, stickvacs, central vacuum systems, and combination cleaners.

1.3 This test method applies to test dust removal from floor coverings not the removal of surface litter and debris.

1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.5 This test method may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM E133-92(2016) : Standard Specification for Distillation Equipment

September 26, 2016, 4:09 am

≫ Next: ASTM E1545-11(2016) : Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis

≪ Previous: ASTM F2608-15e1 : Standard Test Method for Determining the Change in Room Air Particulate Counts as a Result of the Vacuum Cleaning Process

$

0

0

1.1 This specification covers distillation equipment used in the following ASTM test methods: D86, D850, and (for approved alternative requirements only) Test Method D1078.

1.2 Some items of equipment included in this specification are common to all methods; other items are not. Therefore, those portions of this specification pertinent to the need must be selected.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM E1545-11(2016) : Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis

September 26, 2016, 4:09 am

≫ Next: ASTM F1431-92(2016) : Standard Specification for Water Trap for Diesel Exhaust

≪ Previous: ASTM E133-92(2016) : Standard Specification for Distillation Equipment

$

0

0

1.1 This test method describes procedures for the assignment of the glass transition temperature of materials on heating using thermomechanical measurements under compression experimental conditions.

1.2 This test method is applicable to amorphous or to partially crystalline materials that are sufficiently rigid below the glass transition to inhibit indentation by the sensing probe.

1.3 The normal operating temperature range is from − 100 to 600°C. This temperature range may be extended depending upon the instrumentation used.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 This test method is related to ISO 11359-2. ISO 11359-2 additionally covers the determination of coefficient of linear thermal expansion not covered by this test method. This test method is related to IEC 61006 but uses a slower heating rate.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

ASTM F1431-92(2016) : Standard Specification for Water Trap for Diesel Exhaust

September 26, 2016, 4:09 am

≫ Next: ASTM D8010-16 : Standard Practice for Determination of Water Soluble Alkali Content in Coal

≪ Previous: ASTM E1545-11(2016) : Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis

$

0

0

1.1 This specification covers the material, dimensions, and construction of diesel exhaust water traps, which shall be required whenever the exhaust is to be expelled through the hull of the vessel.

1.2 The traps are designed to prevent sea backwash from entering the diesel exhaust system.

1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

ASTM D8010-16 : Standard Practice for Determination of Water Soluble Alkali Content in Coal

September 26, 2016, 4:09 am

≫ Next: ASME B31.8-2016 : Gas Transmission and Distribution Piping Systems

≪ Previous: ASTM F1431-92(2016) : Standard Specification for Water Trap for Diesel Exhaust

$

0

0

1.1 This practice describes a procedure for the determination of water soluble sodium as sodium oxide (Na₂O) and potassium as potassium oxide (K₂O) in the analysis of coal samples prepared in accordance with Practice D2013.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This practice is derived in part from the ASME procedure water soluble alkalis.2

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASME B31.8-2016 : Gas Transmission and Distribution Piping Systems

September 26, 2016, 8:38 am

≫ Next: ATIS 0410003-0029 : Unified Ordering Model- Access Service Request UOM-ASR Volume III - Design

≪ Previous: ASTM D8010-16 : Standard Practice for Determination of Water Soluble Alkali Content in Coal

$

0

0

This Code covers the design, fabrication, installation, inspection, and testing of pipeline facilities used for the transportation of gas. This Code also covers safety aspects of the operation and maintenance of those facilities. (See Mandatory Appendix Q for scope diagrams.)

This Code is concerned only with certain safety aspects of liquefied petroleum gases when they are vaporized and used as gaseous fuels. All of the requirements of NFPA 58 and NFPA 59 and of this Code concerning design, construction, and operation and maintenance of piping facilities shall apply to piping systems handling butane, propane, or mixtures of these gases.

---

ATIS 0410003-0029 : Unified Ordering Model- Access Service Request UOM-ASR Volume III - Design

September 26, 2016, 10:52 am

≫ Next: ATIS 0404000-0054 - ATIS-0404028-0054 : Access Service Request Guidelines (ASR)

≪ Previous: ASME B31.8-2016 : Gas Transmission and Distribution Piping Systems

$

0

0

The Unified Ordering Model (UOM) describes a complete set of system documentation using an end-to-end structured methodology. The scope of UOM encompasses business requirements, analysis, design and implementation. Logically, these components are defined within the UOM in four volumes. Volume III focuses on "how" the implementation shall resolve the business requirements. Release of UOM-ASR Volume III, Version 30 is anticipated for March 2017.

ATIS 0404000-0054 - ATIS-0404028-0054 : Access Service Request Guidelines (ASR)

September 26, 2016, 10:56 am

≫ Next: ATIS 0404110-0029 : Unified Ordering Model - Access Service Request UOM-ASR Volume I: Business Requirements For An Electronic Ordering Interface

≪ Previous: ATIS 0410003-0029 : Unified Ordering Model- Access Service Request UOM-ASR Volume III - Design

$

0

0

The Access Service Ordering Guidelines (ASOG) describes the various ordering forms used for the purpose of requesting access service to be provided by Providers. These guidelines are equally applicable to manual (paper) and mechanized (electronic) forms of access ordering by Customers when placing an order for access service under the various Provider's Access Service Tariffs. Release of ASOG Version 55 is anticipated for March 2017.

ATIS 0404110-0029 : Unified Ordering Model - Access Service Request UOM-ASR Volume I: Business Requirements For An Electronic Ordering Interface

September 26, 2016, 11:04 am

≫ Next: ATIS 0410002-0029 : Unified Ordering Model- Access Service Request UOM-ASR Volume II - Analysis

≪ Previous: ATIS 0404000-0054 - ATIS-0404028-0054 : Access Service Request Guidelines (ASR)

$

0

0

"The Unified Ordering Model (UOM) describes a complete set of system documentation using an end-to-end structured methodology. The scope of UOM encompasses business requirements, analysis, design and implementation. Logically, these components are defined within the UOM in four volumes. Volume I provides an explanation of the business requirements and a high-level conceptual overview of the solution. It also includes the Business Process Definition, Business Validation Rules, Scenarios and Activity Diagrams. Release of UOM-ASR Volume I, Version 30 is anticipated for March 2017. "

ATIS 0410002-0029 : Unified Ordering Model- Access Service Request UOM-ASR Volume II - Analysis

September 26, 2016, 11:12 am

≫ Next: IEEE P802.1AEcg : IEEE Draft Standard for Local and metropolitan area networks--Media Access Control (MAC) Security - Amendment 3:Ethernet Data Encryption devices

≪ Previous: ATIS 0404110-0029 : Unified Ordering Model - Access Service Request UOM-ASR Volume I: Business Requirements For An Electronic Ordering Interface

$

0

0

The Unified Ordering Model (UOM) describes a complete set of system documentation using an end-to-end structured methodology. The scope of UOM encompasses business requirements, analysis, design and implementation. Logically, these components are defined within the UOM in four volumes. Volume II is an analysis of the requirements to define ""what"" the proposed technical resolution needs to support. It is a logical view of the proposed solution, which meets the business need, and it is not based on any particular software protocol. Release of UOM-ASR Volume II, Version 30 is anticipated for March 2017.

IEEE P802.1AEcg : IEEE Draft Standard for Local and metropolitan area networks--Media Access Control (MAC) Security - Amendment 3:Ethernet Data Encryption devices

September 26, 2016, 6:15 pm

≫ Next: IEEE PC57.15 : IEEE Draft Standard Requirements, Terminology, and Test Code for Step-Voltage Regulators

≪ Previous: ATIS 0410002-0029 : Unified Ordering Model- Access Service Request UOM-ASR Volume II - Analysis

$

0

0

Amendment Standard - Unapproved Draft.

IEEE PC57.15 : IEEE Draft Standard Requirements, Terminology, and Test Code for Step-Voltage Regulators

September 26, 2016, 6:15 pm

≫ Next: BS EN 60965:2016 : Nuclear power plants. Control rooms. Supplementary control room for reactor shutdown without access to the main control room

≪ Previous: IEEE P802.1AEcg : IEEE Draft Standard for Local and metropolitan area networks--Media Access Control (MAC) Security - Amendment 3:Ethernet Data Encryption devices

$

0

0

Revision Standard - Unapproved Draft.

BS EN 60965:2016 : Nuclear power plants. Control rooms. Supplementary control room for reactor shutdown without access to the main control room

September 27, 2016, 1:54 am

≫ Next: BS EN 62625-2:2016 : Electronic railway equipment. On board driving data recording system. Conformity testing

≪ Previous: IEEE PC57.15 : IEEE Draft Standard Requirements, Terminology, and Test Code for Step-Voltage Regulators

$

0

0

Cross References:
IEC 60709
IEC 60964:2009
IEC 61226
IEC 61513
IEC 61771
IEC 62646
ISO 11064
ISO 11064-1
ISO 11064-3
ISO 11064-6
IAEA SSR-2/1:2012
IAEA NS-G-1.3:2002
EN 60709
EN 60964:2010
EN 61226
EN 61513
EN ISO 11064
EN ISO 11064-1
EN ISO 11064-3
EN ISO 11064-6
IEC 60780
IEC 60880
IEC 60980
IEC 61227
IEC 61508-1
IEC 61508-2
IEC 61508-3
IEC 61508-4
IEC 61772
IEC 61839
IEC 62138
IEC 62241
IEC 62645
ISO 9241
IAEA GS-R-3:2006
GS-G-3.1:2006
GS-G-3.5:2009
IAEA SSR-2/2
NS-G-1.3:2002


All current amendments available at time of purchase are included with the purchase of this document.

---

BS EN 62625-2:2016 : Electronic railway equipment. On board driving data recording system. Conformity testing

September 27, 2016, 1:54 am

≫ Next: BS EN 62822-2:2016 : Electric welding equipment. Assessment of restrictions related to human exposure to electromagnetic fields (0 Hz to 300 GHz). Arc welding equipment

≪ Previous: BS EN 60965:2016 : Nuclear power plants. Control rooms. Supplementary control room for reactor shutdown without access to the main control room

$

0

0

Cross References:
IEC 60571
IEC 61375
EN 61375
IEC 62498-1
IEC 62625-1:2013
EN 62625-1:2013
ISO/IEC 8824


All current amendments available at time of purchase are included with the purchase of this document.

BS EN 62822-2:2016 : Electric welding equipment. Assessment of restrictions related to human exposure to electromagnetic fields (0 Hz to 300 GHz). Arc welding equipment

September 27, 2016, 1:54 am

≫ Next: BS EN 62631-3-1:2016 : Dielectric and resistive properties of solid insulating materials. Determination of resistive properties (DC methods). Volume resistance and volume resistivity. General method

≪ Previous: BS EN 62625-2:2016 : Electronic railway equipment. On board driving data recording system. Conformity testing

$

0

0

Cross References:
IEC 60050-851:2008
IEC 60974-1
EN 60974-1
IEC 60974-6
EN 60974-6
IEC 61786-1
EN 61786-1
IEC 61786-2
EN 61788-2
IEC 62822-1
EN 62822-1
IEC 62226-1
EN 62226-1
IEC 62226-2-1:2004
EN 62226-2-1:2005
IEC 62311
EN 62311
1999/519/EC
2013/35/EU
IEEE C95.1:2005
IEEE C95.6:2002
IEEE C95.3.1:2010


All current amendments available at time of purchase are included with the purchase of this document.

BS EN 62631-3-1:2016 : Dielectric and resistive properties of solid insulating materials. Determination of resistive properties (DC methods). Volume resistance and volume resistivity. General method

September 27, 2016, 1:54 am

≫ Next: BS EN 62591:2016 : Industrial communication networks. Wireless communication network and communication profiles. WirelessHART^T^M

≪ Previous: BS EN 62822-2:2016 : Electric welding equipment. Assessment of restrictions related to human exposure to electromagnetic fields (0 Hz to 300 GHz). Arc welding equipment

$

0

0

Cross References:
IEC 60212
EN 60212
IEC 60455
EN 60455
IEC 60464
EN 60464
IEC 61212
EN 61212
ISO 868
EN ISO 868
IEC 60050-121
IEC 62631-3-11


All current amendments available at time of purchase are included with the purchase of this document.

BS EN 62591:2016 : Industrial communication networks. Wireless communication network and communication profiles. WirelessHART^T^M

September 27, 2016, 1:54 am

≫ Next: BS EN 60384-18:2016 : Fixed capacitors for use in electronic equipment. Sectional specification. Fixed aluminium electrolytic surface mount capacitors with solid (MnO$d2) and non-solid electrolyte

≪ Previous: BS EN 62631-3-1:2016 : Dielectric and resistive properties of solid insulating materials. Determination of resistive properties (DC methods). Volume resistance and volume resistivity. General method

$

0

0

Cross References:
IEC 61158-1:2014
EN 61158-1:2014
IEC 61158-2
EN 61158-2
IEC 61158-3-20:2014
EN 61158-3-20:2014
IEC 61158-4-20:2014
EN 61158-4-20:2014
IEC 61158-5-20:2014
EN 61158-5-20:2014
IEC 61158-6-20:2014
EN 61158-6-20:2014
IEC 61784-1:2014
EN 61784-1:2014
IEC 61784-2
EN 61784-2
ISO/IEC 7498-1
ISO/IEC 7498-3
ISO/IEC 8824
ISO/IEC 8859-1
ISO/IEC 9545
ISO/IEC 10731
IEEE 802.15.4:2011
IEEE 802.15.4e:2012/A1
IEEE 802:2001
ISO/IEC/IEEE 60559
IEC 61158-6-9:2014
EN 61158-6-9:2014
IEC 62657-2:2013
EN 62657-2:2013
IEC 62657-2:2013
EN 62657-2:2013
IEC 60050
ISO/IEC 8822
ISO/IEC 8825-1
ISO/IEC 15408
ETSI EN 300 328:2012
ETSI EN 300 440-2:2010
1999/5/EC
2014/53/EU
IEEE 754:2008
IEEE 802.3
IEEE 802.11
NIST 800-38C:2004
NIST FIPS 140


All current amendments available at time of purchase are included with the purchase of this document.

BS EN 60384-18:2016 : Fixed capacitors for use in electronic equipment. Sectional specification. Fixed aluminium electrolytic surface mount capacitors with solid (MnO$d2) and non-solid electrolyte

September 27, 2016, 1:54 am

≫ Next: BS 7668:2016 : Weldable structural steels. Hot finished structural hollow sections in weather resistant steels. Specification

≪ Previous: BS EN 62591:2016 : Industrial communication networks. Wireless communication network and communication profiles. WirelessHART^T^M

$

0

0

Cross References:
IEC 60063
EN 60063
IEC 60068-1:2013
EN 60068-1:2014
IEC 60068-2-58:2015
EN 60068-2-58:2015
IEC 60384-1:2016
EN 60384-1:2016
IEC 60417
IEC 61193-2:2007
EN 61193-2:2007
ISO 3


All current amendments available at time of purchase are included with the purchase of this document.